Machine for removing pits from cherries, plums, apricot 1000

Machine for removing pits from cherries, plums, apricot 1000 – 2000 kg/h

Technical data:

Main drive: capacity - 2.2 kW

Output revolutions: a 7.3-47 min.

Drive of the brushes: power - 0.37 kW

Drive cutting unit: power - 0.37 kW

Drive vibration table: power - 0.75 kW

Dimensions:

Length: 3020 mm, no of: 2800 mm

Width: 1350 mm

Height: 1750 mm

Weight: 1800 kg

Staff: 1-2 persons.

Control the speed of the machine is actuated (CVT) with adjustable frequency of rotation, which ensures the adjustability of the process of pitting in the range of 7.8 to 47 beats per minute. To setup and run the device installed on it a hand wheel and selector switch for manual operation. Brush and cutting the node have the independent drive. Evenly silent running of the chain is ensured by the guide rollers and guide rails made of polyamide. Punches (knives) for extruding bones, placed on pancontinental, which moves on rails racks.

The process of removing seeds:

After the washing machine fruit fruit fall into the receiving node directly onto a plate to remove the bones. Fruits that do not fall into the holes of the plates are swept back to the receiving node with a brush. Intermittently moving the plate with the fruit gradually comes in the position of pitting. Deleted the bones pass through the rubber sleeve and fall into a discharge screw conveyor. After removal of the seed fruits in plates falling on the slope falls into the collection container or shipping tape. Stuck in the plates, the fruits are pushed by the plate to set her tappets, placed on the reverse side of the plate.

Cutting the knot:

Node is installed separately on the device, with the goal of providing aesthetic removal of seeds from different fruits. Rotating disc knives cut the knot cut the fruit before the extruding phase of the bones. In the process of notching the fruits are held in proper position by a cylindrical supporting brushes. The knives for knocking bones, combined with a dividing knife, remove the bones, at the same time dividing the fruit into two halves.

Vibrating table:

If necessary, the machine can be set vibrating device with a separate electric drive. This site improves the aesthetics of the fruit after removal of seed, helps clean the fruits, remove possible small fruit chips, small remnants of bones.

The size of the holes of the plates:

1.In the processing of cherries:

The holes are made with a tolerance of 4 mm. This means that if the hole diameter is 24 mm, in a plate without problems removed from the fruit pits with a diameter of 20-24 mm. If the deviation is greater than this, it is recommended to re-calibrate the cherries.

2.In the processing of plums:

As the fruits have oval form, they are recommended to be installed in a perpendicular position because only in this case will get beautifully bisected fruit. It does not hurt to comply with the following:

the maximum fruit diameter should match the diameter of the holes;

- the minimum diameter of the fruit is only 2-3 mm must be less than the diameter of the holes.

3.In the processing of apricots/peaches:

Apricots and peaches are the so - called neolentinus (not placed in a specific orientation) varieties of fruit, therefore, of 15-20 % of bone is removed in vertical position, often the fruit splits at the bottom. So if you want a canned product with a beautiful aesthetic appearance, it is recommended to install a sorting line. The size of the holes should be chosen in accordance with the size of a large fruit. The maximum permissible deviation is 5 mm.

Plate to remove the bones:

Plum: diameter of holes 26; 29; 31; 34. Capacity – up to 2000 kg/hour.

Greengage: the diameter of the holes – 34; 37; 40; 42. Capacity – up to 2000 kg/hour.

Cherry: the diameter of the holes– 19,5; 21; 22,5; 24; 26; 28. Productivity 1000 kg/hour.

Small cherry: the diameter of the holes– 18; 19,5; 21; 22,5; 24. Production capacity – 1600 kg/h.

Apricots and peaches: the diameter of the holes– 40; 43; 46; 49; 51. Capacity – 2000 kg/hour.

Best offer You will get on request at our email address: office@ar-tech.com.ua.

We will answer all Your questions by phone: +380997174185 / +380970308051, +380953376425, or e-mail.

The proposal provided on request.

The price on the website may differ from the actual.

Waiting for Your requests.

Sincerely yours, the company AR-of Those.

machine to remove the seed, remove seeds from cherries to remove the pits from the cherries, the machine for removing pits from the cherries, removing pits from the cherries, removing the pits of cherries, remove pits from cherries, kostochkovaja machine, kostochkovye equipment, machine removal, machine for removing seeds from apricot, knockout pits from plums, knocking out seeds from cherries, knocking out the seeds from apricots, kostochkovaja machine for cherry, plum pitter, pitter apricot, destoning cherry pitter, plum destoning, automatical cherry pitter,